Home Products

Automatic Clamp System

Features
    • Very secure clamping systems
    • Wide range of different models
    • Greatly reduces die and mold change times

Introduction

Forwell specializes in the production of Automatic Clamp Systems with a wide range of models specially designed to fit your dies and plates. With over 20 years experience in the industry you can rest assured that Forwell will deliver the highest quality clamps for your machining operations.

There are a wide range of different models available but the three most popular automatic clamping systems are the TAX Pneumatic Type Clamp System, the TR 90° Rotating Die Clamp and the TS Swing Type Clamp.

Effects Of Introducing DCSL

Before
After
01
Manual Operation
Automation
02
While Die/Mold changing, it takes long time and manpower to tighten.
Only touch the buttons on the control panel.
03
The tightening force will be different by different operators.
The clamping force is the same. Increased safety.
04
Operators waste much manpower, increased injury happened.
By control panel, operators save manpower and decrease injury happened.
05
No alarm notification while the screws are loosing.
With alarm device, the machine will stop immediately.

System Selection

Forwell specializes in the production of Automatic Clamp Systems with a wide range of models specially designed to fit your dies and plates. With over 20 years experience in the industry you can rest assured that Forwell will deliver the highest quality clamps for your machining operations.
There are a wide range of different models available but the three most popular automatic clamping systems are the TAX Pneumatic Type Clamp System, the TR 90° Rotating Die Clamp and the TS Swing Type Clamp.

The TAX system uses an automatic pneumatic pressure mechanism to individually clamp upper dies. This system is well suited for both smaller and larger hydraulic presses.

 
Clamp F N P
TAX-4 68 68 24
TAX-6 78 73 16
TAX-10 98 79 6


 

The TR system uses a hydraulic mechanism with a 90° turning movement to lock molds and dies into position. This heavy duty Clamping System is available in three different models with a clamping force up to 16 tons

Proof Pressure 27.0MPa(275kgf/cm2)
Max Working Pressure 18.1MPa(185kgf/cm2)
Working Pneumatic Range 0.4~0.7(4~7kgf/cm2)
Ambient Temperature Range -5~60°C
Hydraulic Fluid ISO VG32~VG56
Model Clamping force(at 185kgf/cm2) Requited Qrantity(cc.) A±1 MIN.B MIN.C
TR-6 6 32.5 40 75 25
TR-10 10 52.5 50 95 30
TR-16 16 84.0 60 110 35
Model D E F G J K M N PT Q R
TR-6 112 70 M8*16 Deep M12*20 Deep 64 30 32 148 1/4 79 22
TR-10 116 70 M14*30 Deep M14*30 Deep 84 35 40 158 3/8 89 27
TR-16 120 76 M14*35 Deep M14*35 Deep 99 40 50 168 3/8 94 32
Model T U V W X kg Maxx
TR-6 235 15 61 108 44 20
TR-10 252 16 74 110 49 25
TR-16 267 16 79 115 54 27

The TAX system uses an automatic pneumatic pressure mechanism to individually clamp upper dies. This system is well suited for both smaller and larger hydraulic presses.

Proof Pressure 275kgf/cm2
Max Working Pressure 185kgf/cm2
Ambient Temperature Range -5~60°C
Hydraulic Fluid ISO VG32~VG5656
Microswitch Type Z-15G-Q-22B
Type of Contact Single Pole Double Throw
Rating AC125V, 20A
DC 30V, 6A6A
Model A B C D E F G BB Z J K M
TS-4 94 27.5 95 22.5 50 28 28 52 115 28 16 230
TS-10 129 34.5 110 25 60 36 30 60 129 32 20 280
TS-16 168 35.5 150 25 100 44 35 68 168 38 20 348
Model N O P Q R S T U V W X Y
TS-6 16 135 24° 55 55 60.5 55 15.5 19.5 143.5 5 2.5
TS-10 20 150 21° 70 68 75 70 11 19 178 5 2.5
TS-16 20 190 36° 85 93 102.5 85 21 19 226 6 3